null

MADE IN THE USA

About GenRight's Suspension Systems...

• Proven quality, performance and durability.
• Utilize the GenRight gas tank to allow more room or bigger axles.
• Are weld-on for optimal bracket location(s) and so nothing hangs down.
• Move the spring and dampening control out the wheels (in the optimal position).
• Use higher quality thicker materials for long term durability.
• Use proven quality Genuine Johnny Joints (serviceable).
• Utilize Top quality coilover shocks (King, Fox or Bilstein) with GenRight’s spec valving, spring rates and hose routing.
• Are quiet because of the bind free GenRight 3 link front and 4 link rear suspension.
• Keep the steering box for optimal performance! We have our own spec ram assist kits.

• Designed around high pinion Currie axles that are custom built to GenRight’s specs for best durability and performance off-road.

100% American Made!


Turn your TJ into an LJ!

This simple kit will give you the same up travel we offer in our Tracer coil over shock suspension kit.

All parts are key notched (puzzled) to fit together and self fixture for easy assembly by the installer.

When done, your TJ will even take a factory Jeep Unlimited LJ hard top or soft top!

The GenRight Legend Kit is our original suspension designed for the do-it-yourselfer with a CJ, YJ, TJ or LJ. Available in single or double triangulated version. It allows you to do a little bit at a time, pick your own desired wheelbase, axles (brand and width), tire size and drivetrain combo.

 
The GenRight Tracer kit is geometry that was off-road race Inspired, this “system” is designed for the highest level of performance for their Jeep on AND off road. Longer wheelbase, lower center of gravity, without sacrificing suspension travel. Specifically designed for a Chevy LS3 & 4L80 transmission (or stock drivetrain), Currie axles, & Atlas transfer case.


  • Universal Urethane Bump Stop (Pair) w/ Bump Cans Same length as a compressed air bump stop, so you can upgrade down the road Shown here on the rear suspension with coil over shock Shown here on the front suspension set up for a coil over shock

    GenRight

    Universal Urethane Bump Stop (Pair) w/ Bump Cans

      This is the GenRight "Rock Stomper" Urethane bump stops. It is a simple and low cost solution for bump stops on a Jeep! Here is how it works: These Urethane Bump Stops fit in a KING 2.0" diameter air bump can. This allows you to...

    $299.99
  • Reverse Twisted Pitman Arm GenRight's Reverse Twisted Pitman Arm, STK-2540
Shown here on a JK steering box in the GenRight 4500 car

    GenRight

    Reverse Double Shear Pitman Arm

    This is the innovative GenRight Reverse Twisted Pitman Arm to correct the angle issues inherent in hi-steer set ups (on long travel suspension systems using heims). This same pitman arm we used in Jordan's 4585 MOD Class racer with a JK...

    $469.99
  • 8" Upper Control Arm Mount (Axle Side), BKT-3280 8" Upper Control Arm Mount (Axle Side) Assembly

    GenRight

    8" Upper Control Arm Mount (Axle Side)

    This is the GenRight 8" tall Universal Control Arm Mounting Bracket. It is designed to be welded on the Axle Side and can be cut down to fit any vehicle application.The mount is universal and can be cut or trimmed to be mounted at any height...

    $59.99
  • This is the GenRight axle side Front Trac Bar mount for the Jeep JK & JKU Comes with a 3/4" Grade 8 Bolt, Washers, and Uni-Torque Nut Axle side bracket welded on the axle tube in the proper location Back side view of the axle side Trac Bar bracket welded on the axle tube Axle side bracket welded on the axle tube in the proper location

    GenRight

    Jeep JK Axle Side Trac Bar Mount (2 or 4 Door)

    This is a Heavy Duty GenRight axle side Trac Bar mount for the Jeep JK, 2 or 4 door when using the GenRight coil over suspension with a Currie (60 or 70) axle. It keeps the front axle under your Jeep and we work hard to keep the trac bar as...

    $99.99
  • GenRight's Axle Side 20 degree Lower Control Arm Mount One piece design allows for more weld surface to the axle tube

    GenRight

    20 Deg Lower Control Arm Brackets

    These are top quality 20 Degree lower control arm mounting brackets from GenRight Off Road. Heavy Duty 1/4" thick is precision formed into shape so the mounting holes line up perfectly. Unlike the old days where fabricators just welded individual tabs...

    $69.99
  • Rear 4-Link Rear Bracket Kit (Chassis Side) 3 Hole, Fully Welded  4 Link Rear Bracket Kit, 3 Hole installed Rear 4-Link Rear Bracket Kit (Chassis Side) 3 Hole

    GenRight

    Rear 4-Link Rear Bracket Kit (Chassis Side) 3 Hole

    This is our original 3 hole version of the "builders" Triangulated 4 link rear suspension bracket kit. We have figured out all the mounting points for proper geometry (weight transfer, rear steer and minimal anti-squat, etc.) to make your rig...

    $449.99
  • Twisted pitman arm and the twisted mount for the hi-steer arm. Closeup of the mount on a hi-steer arm Here you can see how both are twisted to improve range of motion Includes a plastic cap to protect the internal threads on the pitman arm

    GenRight

    Twisted Pitman & Hi-Steer Mount

    This is the GenRight Twisted Pitman Arm and Hi-Steer Arm Mount for drag links with heims on both ends. It includes our Twisted Pitman Arm and our Hi-Steer Arm Mount kit to correct the angle issues inherent in long travel front...

    $499.99
  • TJ to LJ Body Extension Panel with soft top lip. TJ to LJ Body Extension Panel pieces. Easily welded into place to look completely factory!

    GenRight

    TJ to LJ Body Extension Panels

    This is the formed sheet metal pieces you need to fill the 15" gap in your tub when using our TJ to LJ conversion kit. Once done, a factory LJ Hard top or Soft top will fit your TJ. Features: Two pieces for each side (4 pieces total). Same...

    $99.99
  • Jeep LJ Tracer Stretch Corner Guard Set - Aluminum Here is how it works, we move the entire wheel opening back 4" Shown here with a EXT flare to move the axle even further back!

    GenRight

    Tracer Stretch LJ Corner Guard Set - Aluminum

    This is the Aluminum "Full" type Corner Guard for the UnlimitedJeep Wrangler LJ with STRETCH FENDER WELL location for the GenRight Off Road TRACER suspension. Features: Laser cut and shape is formed with a custom "one hit" die to assure a...

    $899.99
  • GenRight's Short Rear Shock Towers, RSM-1000 Shown here is an outboard shock tower with remote res Raise up the entire shock and move it outboard for better dampening control Another mounting solution with this rear shock tower

    GenRight

    Universal Outboard Rear Shock Tower Kit, Short

    This is a SHORTER and thinner version of our RSM-1001 outboard rear shock towers for the Jeep Wrangler TJ, Jeep LJ, Jeep YJ or CJ-7. It is designed to accept 2.0" shocks. It is a perfect way to convert your rig to outboard mounted...

    $249.99
  • GenRight STK-2503 Drag Link Correction Kit GenRight's Drag Link Correction Kit installed

    GenRight

    Drag Link Correction Kit

    This is the GenRight Drag Link Correction Kit with heims rod ends. This kit will correct the angles and issues inherent in long travel front suspensions (issue being; not enough down travel on the drag link heims when both pitman arm and...

    $799.99
  • 3 Link Front & 4 Link Rear Bracket Package

    GenRight

    3 Link Front & 4 Link Rear Bracket Package

      This is a "builders" PACKAGE with a 3 Link front and 4 Link rear suspension bracket kit(s).   This is your chance to get extra $$$ OFF our normal good deal!Designed to fit a TJ or YJ (but can modified to fit a CJ), this is...

    $799.99
  • 6" Upper Control Arm Mount (Axle Side) w/ Gussets, BKT-3260 6" Upper Control Arm Mount (Axle Side) Assembly

    GenRight

    6" Upper Control Arm Mount (Axle Side)

    This is the GenRight 6" tall Universal Control Arm Mounting Bracket. It is designed to be welded on the Axle Side and can be cut down to fit any vehicle application. The mount is universal and can be cut or trimmed to be mounted at any...

    $59.99
  • Jeep TJ/LJ Heavy Duty Trac Bar Kit Axle Side of the TJ Trac Bar Bracket Shown here is how the backside of the bracket boxes in around the frame too. Shown here with Twisted pitman arm and mounted on the side of the TJ frame. Laser cut plates show how the mount box around the Jeep TJ frame.

    GenRight

    Jeep TJ & LJ Heavy Duty Trac Bar Kit

    This is the Heavy Duty GenRight Front Trac Bar Kit to keep the front axle under your Jeep. The materials used are twice as thick as stock! This builders kit comes with the Johnny Joint pre-welded on one side and the tubing...

    $649.99
  • Jeep JK & JKU Trac Bar w/Frame Side Mount from the Elite 3 Link Suspension kit Here you can see the slight bends in the 1/4" thick wall CrMo tubing 1/4" thick frame side mount fits the frame perfectly Double shear 9/16" Grade 8 Bolt JK Elite Front Trac Bar and mounts, shown here at full bump

    GenRight

    Jeep JK HD Trac Bar w/ Frame Mount (2 or 4 Door)

      This is a Heavy Duty GenRight Front Trac Bar Kit for the Jeep JK, 2 or 4 door when using the GenRight coil over suspension with a Currie (60 or 70) axle. It keeps the front axle under your Jeep and we work hard to keep the trac bar as...

    $749.99
  • GenRight Off Road Rear Sway Bar Kit for the Jeep LJ with Tracer Suspension Shown here installed on Jeep LJ frame with GenRight Tracer Suspension System

    GenRight

    Tracer Jeep LJ Rear Sway Bar Kit

      This is the GenRight rear sway bar kit to fit our "Tracer" Jeep LJ Suspension Kit This kit was designed to add stability to your lifted or long travel Jeep Wrangler LJ. It is a weld-on kit. Our sway bar is about 30% stiffer than...

    $849.99
  • High Capacity Fuel Tank for the Tracer Suspension View of the axle side of the High Capacity Fuel Tank for the Tracer Suspension Side view of the High Capacity Fuel Tank for the Tracer Suspension 100% TIG Welded 1/8" thick Aluminum Tank Here you can see the fit using a Currie 70 rear axle and the 6053 tank

    GenRight

    26 Gal Gas Tank for Tracer Susp w/7" Stretch

    This is the larger capacity fuel tank is designed to work with the GenRight Tracer Suspension System in a stretched Jeep Wrangler LJ. Fully assembled and designed to accept the factory Jeep 05-'06 fuel pump module (or the Aeromotive Phantom in-tank fuel...

    $1,949.99
  • BMT-2051 GenRight's Heavy Duty Body Mounts for the Jeep TJ or LJ Before - with factory body mounts on the frame

    GenRight

    Heavy Duty Body Mount Kit, TJ / LJ

    This is a Heavy Duty body mount kit from GenRight Off Road. It replaces the stock thin & cheesy body mounts that are easily smashed and deformed. These new mounts are Laser cut from Heavy Duty 3/16" thick plate steel. This model body mount...

    $179.99
  • All new aluminum cargo area for your Jeep TJ Integrated fuel pump access panel into new cargo area floor New fender wells use the corner guard bolts to hold them in place (no extra holes to be drilled) Cargo area body mounts to the frame are maintained and support the rear floor This is how it looks after cutting out the stock cargo area floor.

    GenRight

    TJ to LJ Cargo Area Kit

    This is our TJ to LJ Cargo Area Kit for our TJ to LJ Frame Stretch Kit. Hide all the cut and stretched sheet metal with this high quality aluminum cargo area interior. It is easy to install, because it uses all the same holes that your GenRight corner...

    $1,899.99
  • GenRight's CrMo Tie Rod and Drag Link with 7/8" Heims and 3/4" Bolts. Here you can see the GenRight CrMo Tie Rod & Drag Link with 7/8" Heims and 3/4" Bolts installed. GenRight's CrMo Tie Rod and Drag Link with 7/8" Heims and 3/4" Bolts on a Dynatrac ProRock GenRight's CrMo Tie Rod and Drag Link on a Currie RockJock 60 STK-8750 CrMo Tie Rod and Drag Link kit on a Currie Rock Jock 60 w/aluminum knuckles

    GenRight

    Chromoly Tie Rod & Drag Link Kit - 3/4" Bolts

    This is the GenRight "builders" steering (Drag Link and Tie Rod) kit. It is a perfect compliment to our Front 3 Link suspension kit and can be cut to fit any vehicle (including a Jeep JK, TJ, LJ, CJ or YJ) or axle width and...

    $999.99 - $1,029.98
  • GenRight's 3/4" CrMo Tie Rod Steering, STK-5750 CrMo tie rod with 7/8" Heims on a Dynatrac front axle Here is how you make it double shear CrMo tie rod with 7/8" Heims on a Currie front axle CrMo tie rod with 7/8" Heims on a Currie Rock Jock 60 front axle

    GenRight

    Chromoly Tie Rod Kit - 3/4" Bolts

    This is the GenRight Tie Rod kit. It is a perfect upgrade for any vehicle with Dana 60 or bigger front axle. This kit is made up of the best component available! This Heavy Duty kit will hold up to big tires and off-road abuse. Got a...

    $549.99 - $579.98
  • Universal GenRight Trac Bar with Currie Johnny Joint on one end and Heim on the other Shown here mounted using the GenRight frame side bracket and a Gr8 9/16" bolt

    GenRight

    Heavy Duty Trac Bar, Only

    This is the Heavy Duty GenRight Front Trac Bar ONLY (mounting brackets sold separately).This product is still considered part of our "builders" product line, since it requires the end user to properly cut it to size and weld in the threaded...

    $549.99
  • GenRight Billet twisted pitman arm Heat Treated Chromoly provides incredible strength and durability. GenRight Billet twisted pitman arm Arm is twisted for optimal geometry GenRight Billet twisted pitman arm

    GenRight

    Billet Chromoly Twisted Pitman Arm

    This is the new and innovative GenRight Billet Twisted Pitman Arm that allows for 3.5" more up travel. This arm was designed as part of our new low ride height TRACER Suspension system for the Jeep LJ. It corrects the angle issues inherent in...

    $899.99
  • GenRight's Jeep Wrangler TJ "Tracer" Suspension Kit TJ Tracer frame side control arm mounts and skid plate installed Jeff testing the TJ Tracer kit out on the trail TJ Tracer frame side control arm mounts and skid plate installed Good picture of ride height compared to Terremoto

    GenRight

    Jeep Wrangler TJ "Tracer" Suspension Kit

    This is GenRight Off Road's Tracer center section for the Jeep Wrangler TJ, 1997 - 2006. This is a scaled down version of our famous LJ Tracer suspension system which has all the proven suspension geometry from our 4500 Class off-road race Jeep...

    $1,999.99
  • GenRight 5/8" CrMo Tie Rod Builders Kit, STK-5625 GenRight Heim style High Steering on Dana 44 knuckles

    GenRight

    Chromoly Tie Rod Kit - 5/8" Bolts

    This is the GenRight TIE ROD kit, it is a perfect upgrade for any vehicle with a Dana 30 or 44 front axles. This kit is made up of the best components available! This Heavy Duty kit will hold up to big tires and off-road abuse. Got a...

    $499.99
  • Ram Assist XD Kit from PSC for 38"-42" Tall Tires PSC '95-'02 TJ/XJ/YJ Stage 5 Cylinder Assist Kit

    PSC

    PSC '95-'02 TJ/XJ/YJ Stage 5 Cylinder Assist Kit

      Designed for Extreme Off Highway driving and 38" to 42" tall tires.-Provides double the turning force-Reliefs stress on steering box and frame mounts-PSC ram assist is the ultimate steering stablizerCylinder Assist does not improve your...

    $2,720.00
  • Currie short arm suspension kit for the Jeep TJ or LJ

    RockJock

    Suspension Lift Kit for the Jeep TJ/LJ, CE-9100A

    This is the top quality Rock Jock suspension kit (designed by John Currie). It includes a complete set of 8 genuine Johnny Joint® Control Arms for the 1997-2006 Jeep TJ's and LJ's. All arms are heavy duty and fully adjustable allowing...

    $1,850.00
  • Currie Enterprises Rock Jock 70 Front Axle Currie Enterprises Rock Jock 70 Front Axle 1480 U-joints and Hi-Steer Knuckles are standard on Currie front axles Currie 70 on a Jeep JK build Locking Hubs, over sized brakes and double shear high steer knuckles are standard

    Currie Ent

    Currie Extreme 70 Front Axle - Complete

    This is the race proven Currie Extreme 70 Front Axle. This is the same axle Tony has successfully run in our 805HP V8 powered 4400 Class racer for 7 years and his Terremoto JK!  This is a complete axle (but NO mounting brackets), so it's ready...

    $10,599.99
  • Simple DIY plates that bolt on to check the alignment Alignment tool bolted to front hub Close up of multiple bolt patterns. Close up of the 3 bolt pattern sizes this tool fits View of tool from back side

    GenRight

    DIY Alignment Tool

    This is a pair of Alignment Plate "Tools" for the DIY guy. Simply bolt on to the front hub and check the front side and back side with a tape measure to see how much the toe in or toe out you have.FEATURES include: Precision laser cut and formed...

    $119.99