null

MADE IN THE USA

36 of 70 Items
  • GenRight Off Road's Universal Transmission Crossmember Kit Side view of the GenRight cross member holding trans and t-case in a Jeep build. Close up of the Urethane mount & tabs on each side of this universal cross member kit. Weld the tabs to the inside of the frame so there is clearance for your exhaust. GenRight BKT-1050 in '06 LJ Rubicon with the 6 speed manual.

    GenRight

    Universal Transmission Crossmember Kit

    This is a DIY (do-it-yourself) Universal Cross Member Kit to hold up your transmission (or transfer case). We have designed this kit to be compatible with a wide variety of engine and transmission configurations used in off road Jeeps. The cross...

    $249.99
  • Threaded Step Bungs (Each) - Multiple Sizes 7/8-14 Weld in bung on a steering tie rod and drag link 1-1/4-12 Weld in bung on a control arm with a flex joint 1/2-20 Weld in bung on the end of a sway bar link

    GenRight

    Threaded Step Race Bungs (Each) - Multiple Sizes

    This is a top quality weld-in tube insert or bung (aka; threaded insert). They are CNC machined from cold rolled steel can be MIG or TIG welded into the end of your tubing. The hex head on the end of the bungs we sell stays exposed after being welded...

    $9.99 - $21.98
  • Genuine Rock Jock (Currie) Johnny Joint CE-9114 with 1-1/4"-12 shank How it works: special compound urethane, sintered metal ball, washers and clip Johnny Joints on both ends of GenRight 7075 aluminum control arms Johnny used on an upper control arm of a suspension Johnny Joints on double triangulated rear suspension

    RockJock

    Johnny Joint, 1-1/4 Shank by Rock Jock

    This is a genuine Rock Jock Johnny Joint (by John Currie) with a 1-1/4-12 threaded shank for suspension control arms. A Johnny Joint is a suspension end designed to smoothly rotate up to 30 degrees without binding (or degrading which...

    $66.00
  • GST4053 and GST2053 Frame Sleeves w/ Hardware Close up of the sleeve on forward gas tank mount Sleeve shown here on tank mount. Shown here where they would go thru the frame, on each side

    GenRight

    GST4053 and GST2053 Frame Sleeves

    This is the Frame Sleeve kit for the Jeep TJ or YJ. It necessary if bolting up a GenRight gas tank through the factory frame to keep from crushing the frame when tightening to two forward bolts on the skid plate. One sleeve and bolt is used per side...

    $9.99
  • This is a Non-electric line lock, parking brake, emergency brake We offer two different mounting styles for your application A mounting style for this line lock, parking brake B mounting style for this line lock, parking brake Technical specifications for mounting this hydraulic ball valve

    GenRight

    Ball Valve Parking Brake

    This is a simple (non-electric) hydraulic ball valve assembly that can be used as an inline parking brake. How does it work? You simply step on the brake pedal and turn the lever. It then locks the pressure in the brake line (as if you were...

    $179.99 - $189.99
  • Fuel Pump Access Panel for the Jeep LJ GenRight's fuel tank access plate is cut into the rear floor section of a Jeep LJ

    GenRight

    Fuel Pump Access Panel for the Jeep LJ

    This is the GenRight Off Road rear floor access plate for the wider floor ribs on the Jeep Wrangler Unlimited LJ (all models 2003 to 2006). It allows you access to the top of the fuel tank (pump, electrical, hoses, vents, etc) without...

    $169.99
  • 1.5" - 2" Tubing Couplers (Sold Each)

    GenRight

    1.5" - 2" Tubing Couplers (Each)

    This is a Tube Coupler. They are designed to be strong and perfect for use in situations where you need a removable tube. Simply weld (MIG or TIG) each side into the tube you want to remove. These couplers are meant for use with .120 wall tubing (1.5",...

    $49.99 - $54.99
  • 1/4" Thick Straight Tab (Pair) 1/2" Diameter Hole Typical installation as a lower shock mounts Tab welded onto the inside of the frame

    GenRight

    1/4" Thick Straight Tab (Pair)

    This is a top quality "straight" mounting tab from GenRight Off Road. They are Laser cut from Heavy Duty 1/4" thick plate steel.They are perfect for mounting limit straps or other things on your Jeep. Features: Material - 1/4"...

    $11.99
  • Aluminum Shock Reservoir Mounting Brackets (Pair) Here you can see the mount is bolted or riveted to chassis and the shock res is hose clamped on Here you can see the mount is under the fender shock res is hose clamped on

    GenRight

    Shock Reservoir Mounting Brackets (Pair)

    This is the GenRight universal Shock Reservoir Mounting Brackets (Pair). They are Laser Cut and CNC formed from 6061-T6 Aluminum Alloy, so they will not rust. They are bolted to the body or chassis and the reservoir is hose clamped onto the mount...

    $49.99
  • Johnny Joint for Upper Link on Axle

    RockJock

    Johnny Joint for Upper Link on Axle

    This is the specially machined Johnny Joint® rod end out of the Currie CE-9102K front end housing kit. This joint's outer shell is machined to a 1.795" outer diameter with a flanged edge and is designed to be pressed into the "EAR" on the...

    $73.00
  • 1/4" Thick Radius Tab (Pair)

    GenRight

    1/4" Thick Radius Tab (Pair)

    These are top quality Radius Tabs from GenRight Off Road. They are Laser cut from Heavy Duty 1/4" thick plate steel. They are perfect for mounting limit straps or other things on curved surfaces (axle tubes or knuckles). Features: Material...

    $11.99
  • Billet Door Hinges for the Jeep Wrangler JK & JKU The same hinges Tony runs on his Terremoto Jeep Wrangler JKU Close up of the machine work on these billet hinges

    74Weld

    Billet Aluminum Door Hinges for Jeep Wrangler JK

    Looking for little parts you can get to trick out on your new Jeep Wrangler JK or JKU? Then these CNC Machined Billet Aluminum hinges are just the upgrade that you were looking for! The hinges simply bolt-on where the stock door hinges were. These...

    $289.99
  • Sale
    RivNuts 5/16"-18 (10 Pack)

    GenRight

    RivNuts 5/16"-18 (10 Pack)

    This is the same hi-quality hardware offered by Gen-Right Off Road on all "Full" Corners, Rockers and Tub Panel Guards. RivNuts are the perfect (and permanent) to install attachment points (nuts) in "blind" (double wall areas) on the Jeeps...

    $9.99
  • Jam Nuts (Various Sizes), sold each Jam Nut shown here on a control arm with a Johnny Joint Jam nut shown here on steering tie rod and drag link with Heims Jam nut shown here on a sway bar link to lock a heim in place

    GenRight

    Jam Nuts (Each) Multiple Sizes

    Jam Nuts (aka: thin lock hunts) are used to lock (or jam) the threads of a Heim and Johnny Joint in place on sway bar, steering, trac bar or control arms.  They are available in the following sizes: 1/2-20 thread (sway...

    $3.99 - $7.99
  • Sale
    Brake line mounting tabs (Pair) BKT-1250 GenRight Brake line mounting tab

    GenRight

    Brake Line Tabs (Pair)

    This is a top quality "straight" mounting tab from GenRight Off Road. They are Laser cut from Heavy Duty 1/8" thick plate steel.Size: 1" x 1-5/8" long.They are perfect for mounting brake lines or other things on your Jeep. 3/8"...

    $3.99
  • Sale
    RivNuts 1/4"-20 (10 Pack)

    GenRight

    RivNuts 1/4"-20 (10 Pack)

    This is the same hi-quality hardware offered by Gen-Right Off Road on all "Full" Corners, Rockers and Tub Panel Guards. RivNuts are the perfect (and permanent) to install attachment points (nuts) in "blind" (double wall areas) on the Jeeps...

    $8.99
  • Sale
    BKT-5516 GenRight Universal mounting tabs (Pair) Universal mounting tab Exact size

    GenRight

    Universal Mounting Tabs (Pair)

    This is a top quality mounting tab from GenRight Off Road. They are Laser cut from Heavy Duty 1/8" thick plate steel. Perfect for 1/4-20 clip nuts or mounting brake lines.Size: 1-1/4" x 1-1/4" long x 1/8" thick.They are perfect for mounting brake...

    $3.99
  • Steering, misalignment spacers

    GenRight

    Hi-Misalignment spacer (Pair) 3/4 to 5/8

    This is a hi-misalignment spacer for a Heim joint. This part number reduces the bore from 3/4" to 5/8" diameter to fit in our Drag Link Correction Kit. This is the exact same part we run on the drag link (in a LH & RH) of all the GenRight...

    $24.99
  • 1 Set of Billet Door Hinges for the Jeep Wrangler JL or JT Close up of the machine work on the billet hinges, note stainless steel hinge pins They look great on the Jeep! Stock hinge VS Billet hinge Same hinges Tony runs on his Aftershock JLU

    74Weld

    Billet CNC Aluminum Door Hinges for Jeep Wrangler JL

      Looking for little parts you can get to trick out on your new Jeep JL or JT? Then these CNC Machined Billet Aluminum hinges are just the upgrade that you were looking for! Machined finish is stunning and screams "I have trick parts on my...

    $299.99
  • FK Heim Rod End with 1/2"-20 threaded shank Example of the heim being used at the sway bar arm Example of the heim being used at the axle side

    FK Rod Ends

    1/2"-20 FK Heim Rod End (Choose Thread)

    This is a 1/2"-20 FK Heim Rod End. We use these in our GenRight Sway Bar kits. 1/2"-20 Threaded shank with a 1/2" diameter bore.Features: Both Left & Right Hand Threads available. 1/2"-20 threaded shank. Hi strength CrMo body. Hardened...

    $24.99
  • RSMX12 FK Heim Rod End, right hand with 3/4" bore The same FK rod End we use on the tie rod in every GenRight Hi-steer kit Same FK Heims we run on our KOH Ultra4 race buggy! Close up of the same FK Heims we run on our KOH Ultra4 race buggy! 7/8"-14 FK Heim Rod End (Choose Thread)

    FK Rod Ends

    7/8"-14 FK Heim Rod End (Choose Thread)

    This is an American Made fully CrMo (aircraft grade) 7/8" shank x 3/4" bore Heim. The amount of rotation in this rod end is perfect for your steering tie rod (not drag links), because the tie rod does not need hi-misalignment spacers...

    $69.99
  • 5/16" Rivnut Installation Tool Exploded view of the Rivnut tool and parts. Push it into the hole, hold the nut with a wrench and thread the bolt in until it stops After the Rivnuts are installed they sit flush with the body. Here you can see some Rivnuts being used to hold on Corner Guards.

    GenRight

    5/16" Rivnut Installation Tool

    Use this tool to install 5/16-18 (thread) Rivnuts on your off road Jeep Wrangler. Includes: (1) 5/16-18 Rivnut (as pictured) (1) Grade 8 bolt (2) Hardened washers (1) Flange nut. Simply push the assembly into the hole, hold the flange nut with...

    $15.99
  • Replacement Shock Bolt Kit

    GenRight

    Replacement Shock Bolt Kit

    Replacement Shock Bolt Kit This is a direct replacement for the standard shock bolt that comes with all GenRight Suspension Kits. Includes: (1) 1/2-20 x 2-1/2" long Grade 8 Bolt (4) Shock Spacers (2 sizes) (2) Grade 8 Washers (1) 1/2-20 Uni Torque...

    $19.99
  • 1/4" Rivnut Installation Tool Exploded view of the Rivnut tool from GenRight They can be installed using air or electric power tools Here you can see how the Rivnut is flush with the body after installed. Here you can see how the Rivnut is flush with the body after installed.

    GenRight

    1/4" Rivnut Installation Tool

    Use this tool to install 1/4-20 (thread) Rivnuts on your off road Jeep Wrangler. Includes: (1) 1/4-20 Rivnut (as pictured) (1) Grade 8 bolt (2) Hardened washers (1) Flange nut. Simply push the assembly into the hole, hold the flange nut with a...

    $14.99
  • Weld-on Currie Johnny Joint, CE-9110CP w/grease fitting on barrel Here you can see the Johnny Joint TIG welded onto a GenRight trac bar Here you can see the Johnny Joint on the frame side of a GenRight trac bar Here you can see the Johnny Joint on a GenRight trac bar Here you can see the Johnny Joint on the frame side of a GenRight trac bar

    RockJock

    Johnny Joint, weld-on

    This is a weld-on type genuine Rock Jock Johnny Joint (by John Currie) for trac bars or suspension control arms. This joint consists of a 2 ½” O.D. x .180” wall chromoly outer barrel. Interlocking urethane bushings that encase...

    $64.99
  • 5/16"-18 X 1" Flat Head Socket Bolts (10 Pack) Here you can see these countersunk SS bolts on the GenRight rockers and corner guards

    GenRight

    5/16"-18 X 1" Flat Head Socket Bolts (10 Pack)

    This item is a 5/16"-18 X 1" long Stainless Steel Flat Head Socket Bolts (10 Pack). These are the same allen bolts we use in our Rocker Guard Kits, Corner Guard Kits, Tub Panel Guards and More. Accepts a 3/16" allen key wrench. We also sell matching...

    $14.99
  • GenRight Corner Guard Hardware Kit

    GenRight

    GenRight Corner Guard Hardware Kit

    This is a universal Replacement hardware kit for any model GenRight corner guards. It includes 5/16-18 stainless steel flat head allen bolts, washers and nuts (as pictured). It even includes a rivnut installation tool, hinge spacers, tabs to tie into...

    $69.99
  • STK-5755 Hi Steer Knuckle Double Shear Kit Close up of how the kit ties the hi-steer arm and ear on factory knuckle together Shown here with GenRight drag link correction kit and coil over shocks Shown here on a Dana 60 with coil springs, tie rod is lower Simply drill the taper out of the cast iron knuckle with a 3/4" drill bit

    GenRight

    Hi Steer Knuckle Double Shear Kit

    This is the GenRight Kit to Double Shear your steering on your Dana 60 Hi-Steer Knuckles (just like we do on the GenRight Jeep builds). It is a perfect compliment to our CrMo Hi-Steer Tie Rod and Drag Link kit and can be cut to fit any...

    $89.99
  • Steering, misalignment, spacers

    GenRight

    Hi-Misalignment spacer (Pair) 1" to 5/8"

    This is a hi-misalignment spacer for the big "16" size Heim joint. This part number reduces the bore from 1" to 5/8" diameter to fit in our suspension brackets. This is the necessary part to adapt the big FK heim to fit in...

    $24.99
36 of 70 Items