null

MADE IN THE USA

All of GenRight's Suspension Systems:

• Proven quality, performance and durability.
• Utilize the GenRight gas tank to allow more room or bigger axles.
• Are weld-on for optimal bracket location(s) and so nothing hangs down.
• Move the spring and dampening control out the wheels (in the optimal position).
• Use higher quality thicker materials for long term durability.
• Use proven quality Genuine Johnny Joints (serviceable).
• Utilize Top quality coilover shocks (King, Fox or Bilstein) with GenRight’s spec valving, spring rates and hose routing.
• Are quiet because of the bind free GenRight 3 link front and 4 link rear suspension.
• Keep the steering box for optimal performance! We have our own spec ram assist kits.

• Designed around high pinion Currie axles that are custom built to GenRight’s specs for best durability and performance off-road.

100% American Made!


The GenRight Legend Kit is our original suspension designed for the do-it-yourselfer with a CJ, YJ, TJ or LJ. Available in single or double triangulated version. It allows you to do a little bit at a time, pick your own desired wheelbase, axles (brand and width), tire size and drivetrain combo.

GenRight Tracer kit is geometry that was originally off-road race Inspired, this “system” is designed for the person that wants the highest level of performance from their Jeep on & off road. Longer wheelbase, lower center of gravity, & maximum suspension travel. Designed around a Chevy LS3, 4L80 transmission (or stock drivetrain), Currie axles, & Atlas transfer case.

36 of 79 Items
  • GenRight Off Road's Universal Transmission Crossmember Kit Side view of the GenRight cross member holding trans and t-case in a Jeep build. Close up of the Urethane mount & tabs on each side of this universal cross member kit. Weld the tabs to the inside of the frame so there is clearance for your exhaust. GenRight BKT-1050 in '06 LJ Rubicon with the 6 speed manual.

    GenRight

    Universal Transmission Crossmember Kit

    This is a DIY (do-it-yourself) Universal Cross Member Kit to hold up your transmission (or transfer case). We have designed this kit to be compatible with a wide variety of engine and transmission configurations used in off road Jeeps. The cross...

    $249.99
  • Genuine Rock Jock (Currie) Johnny Joint CE-9114 with 1-1/4"-12 shank How it works: special compound urethane, sintered metal ball, washers and clip Johnny Joints on both ends of GenRight 7075 aluminum control arms Johnny used on an upper control arm of a suspension Johnny Joints on double triangulated rear suspension

    RockJock

    Johnny Joint, 1-1/4 Shank by Rock Jock

    This is a genuine Rock Jock Johnny Joint (by John Currie) with a 1-1/4-12 threaded shank for suspension control arms. A Johnny Joint is a suspension end designed to smoothly rotate up to 30 degrees without binding (or degrading which...

    $66.00
  • GenRight's Outboard Rear Shock Mount Kit Close up of JIG welded lower shock mounts, included in this kit. TJ/LJ/YJ/CJ Universal Outboard Rear Shock Mount Kit (Shocks not included) Lower shock mount installs on the back side of the rear axle tube. Outboard Rear Shock Mount Kit Mid-Install (Bump Cans not Included)

    GenRight

    Universal Outboard Rear Shock Mount Kit

    The GenRight outboard rear shock mount kit for the Jeep TJ, LJ, YJ or CJ-7 was designed to accept 2.0" coil over shocks. It is a perfect way to convert your rig to Coilover shocks! The clean and simple design which "frenches"...

    $399.99
  • BMT-2001 GenRight's Hi-Clearance Body Mounts for the Jeep TJ or LJ Before - with factory body mounts on the frame After - with GenRight hi-clearance body mounts on the frame Close up of the new GenRight BMT-2001 body mounts on the frame Easy to see the difference in this picture!

    GenRight

    Body Mount LIFT Kit, TJ / LJ

    This is another innovative and long over due product from GenRight Off Road. It is a new set of hi-clearance body mounts to raise up the 3 mounts on both sides (under the rocker guard) that always get hit on trail obstacles! Yes, we designed...

    $179.99
  • This is how the kit comes, un-assembled This is what the kit looks like after welding GenRight Front 3 Link frame mounting brackets GenRight Front 3 Link frame mounting brackets This is how the frame side 3 link brackets lay out

    GenRight

    3 Link Front Bracket Kit, Chassis side (Unwelded)

    This is what the public has been asking for! A low cost DIY "builders kit" of our popular 3 link Front suspension brackets (not welded). We have figured out all the mounting points for proper geometry (bump steer, anti-squat, etc.) to make your rig a...

    $149.99
  • High Clearance Lower Rear Shock Mount Kit

    GenRight

    High Clearance Lower Rear Shock Mount Kit

      This is the lower rear shock mount (axle side) kit. Similar to our outboard rear shock mount kit, but this is only the lower mounts.This is perfect for someone who already has our kit but is changing axles and who does not want to cut...

    $124.99
  • Twisted Pitman Arm with Removal Tool Arm is twisted for optimal geometry and range of motion from the heim rod end GenRight Twisted Pitman Arm has it's own threaded section for the removal tool Mounted here on a TJ with 5/8" hi misalignment heim on drag link Here you can see the heims are in their neutral position on the drag link

    GenRight

    GenRight Twisted Pitman Arm w/Removal Tool

      This is the innovative Twisted Pitman Arm with Removal Tool from GenRight Off Road! This will correct the stress caused by issues inherent in long travel suspension systems using heims. How? We twisted (or rotated) the drag link...

    $449.99
  • GenRight's Jeep TJ Frame Side Trac bar mount kit. Inside of GenRight's Jeep TJ Frame Side Trac bar mount pieces assembled for picture. GenRight's TJ / LJ Frame Side Trac bar mount pieces as supplied in the kit. GenRight's TJ Frame Side Trac bar mount kit tacked in place on the frame. TJ Frame side trac bar mount kit, fully welded and painted with Twisted pitman arm.

    GenRight

    TJ/LJ Trac Bar Mount (Frame Side)

    This is the GenRight Frame side Trac Bar Mounting Bracket Kit for the Jeep Wrangler TJ or LJ (1997 - 2006). This is the same design we have reliably run on our GenRight Jeeps for years, including on Jordan's 4500 Class KOH racer!Front...

    $99.99
  • Aluminum Shock Reservoir Mounting Brackets (Pair) Here you can see the mount is bolted or riveted to chassis and the shock res is hose clamped on Here you can see the mount is under the fender shock res is hose clamped on

    GenRight

    Shock Reservoir Mounting Brackets (Pair)

    This is the GenRight universal Shock Reservoir Mounting Brackets (Pair). They are Laser Cut and CNC formed from 6061-T6 Aluminum Alloy, so they will not rust. They are bolted to the body or chassis and the reservoir is hose clamped onto the mount...

    $49.99
  • RSM-2150 Rear Coil Spring correction Kit for the Jeep TJ This is the mounting location of the new brackets AFTER GenRight Coil Correction kit is installed BEFORE Coil Correction kit is installed Carefully cut off and clean the frame for the new brackets to be mounted

    GenRight

    Rear Coil Spring Correction Kit

    This is a rear coil spring mounting kit or it can be used as a coil spring correction kit On a Jeep TJ or LJ. This is a low cost way to move the coil spring back on the frame is laser cut and formed from heavy duty 3/16" and 1/4" thick steel and...

    $149.99
  • BKT-3110 lower control arm 10 degree brackets from GenRight Off Road Shown here a the rear axle tube One piece design allows for more weld surface on the axle tube

    GenRight

    10 Deg Lower Control Arm Brackets

    These are top quality 10 Degree lower control arm mounting brackets from GenRight Off Road. Heavy Duty 1/4" thick is precision formed into shape so the mounting holes line up perfectly. Unlike the old days where fabricators just welded individual tabs...

    $69.99
  • 3" Upper Control Arm Mount (Axle Side), BKT-3240 Shown here welded to the top of a rear axle bridge (limit strap tab optional)

    GenRight

    3" Upper Control Arm Mount (Axle Side)

    This is the GenRight 3" tall Universal Control Arm Mounting Bracket. It is designed to be welded on the Axle Side and can be modified to fit any upper control arm vehicle application. The mount is universal and can be cut or trimmed to be...

    $44.99
  • GenRight Twisted Pitman Arm for the Jeep TJ, LJ, YJ Arm is twisted for optimal geometry and range of motion GenRight Twisted Pitman Arm GenRight Twisted Pitman Arm has it's own threaded section for the removal tool Shown here mounted on a Jeep TJ steering box

    GenRight

    GenRight Twisted Pitman Arm

    This is the innovative Twisted Pitman Arm from GenRight Off Road! This will correct the angle issues inherent in hi-steer set ups (on long travel suspension systems using heims). How? We twisted (or rotated) the drag link mounting...

    $399.99
  • King 2.0" Air Bump with Can King 2" air bump on the GenRight Elite Suspension Shown here next to a Jeep TJ frame with King 2.0 can frenched into it. Shown here with GenRight shock mount and frame plate after frenching in can Shown here on the GenRight Growler YJ

    King Shocks

    King Shocks 2.0" Air Bump w/ Can

    This is the King Shocks Brand of 2.0" diameter Air Bump (Sold Each). These are the best air bumps money can buy. This is the same air bump we used on our GenRight Growler Jeep to pre-run for 8 weeks at the Hammers for the 2010 King of the...

    $339.99
  • GenRight Off Road Rear Sway Bar Kit for the Jeep TJ, LJ or YJ Jeep Rear Sway with coil over shock at full droop. Here you can see frame mount for rear sway bar with (white) bearing. Here you can see the axle side mounting and how link fits.

    GenRight

    TJ/LJ/YJ Sway Bar Kit - Rear

      This is the GenRight rear sway bar kit to fit a Jeep TJ, LJ or YJ. This kit was designed to add stability to your lifted or long travel Jeep. It is a weld-on kit. Our sway bar is about 30% stiffer than other brand Anit-Rock type...

    $849.99
  • KING 2.0" Emulsion Coilover Shock An o-ring on the cap keeps dust and dirt from contaminating the valve Tapered spring cup for more clearance during articulation Single allen pinch bolt to release the preload collar. Shown here on the front of a Jeep Wrangler.

    King Shocks

    KING 2.0" (14" Stroke) Emulsion Coilover Shocks

    This is the KING Brand of 2.0" diameter Coil Over Shock, without remote reservoir. These are the best and most quiet coil over shocks you can buy. KING Shocks have a great name in the off-road world. They build an extremely high quality...

  • Jeep JK/TJ/LJ/YJ/CJ Rear Bump Stop Pad Kit SUP-1002 Rear Bump Stop Pad Kit (Assembled, Unwelded) Close up of the GenRight rear bump pad with 14" coil over shock Here you can see how the bump pads engage with the bump stops when flexed Another view on the bump pad mounted on rear axle

    GenRight

    Universal Rear Bump Stop Pad Kit

    This is the axle side, lower bump stop "pad" from GenRight Off Road. A simple and low cost solution for bump stops on your Jeep. Here is how it works: This kit can be installed with our Urethane Bump Stops or King/FOX Shocks 2.0" air bump,...

    $199.99
  • Universal 4 Pass Power Steering Cooler Kit Here you can see how this thin cooler mounts behind the grill

    GenRight

    4 Pass Power Steering Cooler

    This is a 4 Pass cooler (8-1/8" Wide x 5" tall x 3/4" deep), that is an excellent tube-fin heat exchanger, which improves the longevity and overall functioning of your vehicle's power steering system. It installs on the low pressure (return side) of...

    $44.99
  • Jeep TJ/LJ/YJ/CJ-7 Front 3-Link Kit GenRight Front 3-Link w/ Links Installed on Jeep TJ GenRight Front 3-Link w/ Links Installed on BowTie GenRight Front 3-Link Suspension Kit (Skid Plate not Included)

    GenRight

    Front 3-Link Kit (Links Optional)

     Front 3-Link Kit for Jeep TJ, LJ, YJ & More Bind-Free | Street Worthy | Trail Tested | Optimized Geometry | Customizable This is the 3 Link kit from our Legend Suspension kit. It is called 3 link, but is technically a 4 link when you include...

    $1,599.99 - $2,349.99
  • GenRight Axle Side Trac Bar Mount Comes with 3/4" Grade 8 Bolt, Washers, and Uni-Torque Nut Here you can see how trac bar and drag link are parallel. Installed Trac Bar mount

    GenRight

    Universal HD Trac Bar Mount, (Axle Side)

    This is the GenRight Axle Side Trac Bar Mounting Bracket for a front 3 link kit. We have sold and installed 1000's of suspension kits and over time we have made several revisions and upgrades to the component parts. This is the...

    $99.99
  • Twisted Pitman Arm Removal Tool, STK-2520 Tool threads into the internal threads cut into the pitman arm Tool being threaded into the pitman arm for removal from the steering box Be sure to cap off the internal threads from dirt and moisture!

    GenRight

    Twisted Pitman Arm Removal Tool

    This is the Removal Tool (or pitman arm puller) for all the GenRight Twisted Pitman Arms.FEATURES include: CNC machined from tool steel. Hex on the tool is same size (1-5/16") as nut holding the pitman arm on the steering box sector...

    $79.99
  • Jeep TJ/LJ/YJ/CJ-7 Rear 4-Link Rear Kit Jeep on the trail with GenRight Off Road's Jeep TJ/LJ/YJ/CJ Rear 4-Link Rear Kit w/ Links Detail view of GenRight Off Road's Jeep TJ/LJ/YJ/CJ Rear 4-Link Rear Kit w/ Links

    GenRight

    Rear 4-Link Kit (Links Optional)

    Triangulated Rear 4-Link Kit for Jeep TJ, LJ, YJ & MoreBind-Free | Street Worthy | Trail Tested | Optimized Geometry | Customizable Have you been thinking about building your own kit from scratch, or just upgrading to improve the ride quality of...

    $1,499.99 - $2,499.99
  • Steering box brace for the Jeep Wrangler TJ Close up of the clamp for the bottom of the steering box housing Shown here on a GenRight Tracer build

    GenRight

    Steering Box Brace, Jeep TJ (Saginaw box)

      This is a steering box brace for a Jeep Wrangler TJ or LJ Unlimited (with GenRight Tracer Kit installed). This brace ties your Saginaw type power steering box to the passenger frame rail to prevent it from being torn off due to added...

    $89.40
  • SUP-1001 GenRight's front axle bump stop pad kit This is how it looks when the pieces are tacked together Shown here installed with GR Urethane bump stop Rear view of the driver side bump stop mount Side view of the driver side bump stop mount

    GenRight

    Universal Front Bump Stop Pad Kit

    This is the GenRight FRONT bump stop "pad" kit. It is a simple way to get bump stops on the front of your coil over shock Jeep! Since space is limited on the front axle, we designed a combo lower control arm mount with bump stop pad kit. Designed...

    $249.99
  • The 3 Link upper link mount can put on either side by the installer GenRight Front 3 Link frame mounting brackets GenRight Front 3 Link frame mounting brackets This is how the frame side 3 link brackets lay out Drivers side tacked into position on a Jeep TJ frame

    GenRight

    3 Link Front Bracket Kit

    This is the GenRight 3 link Front Bracket Kit for a Jeep Wrangler TJ, LJ or YJ (but can be made to fit the CJ-7 too).Front 3 Link Kit FEATURES: Single upper control arm (to the top of the axle) allows the installer more flexibility to locate...

    $349.99
  • Sale
    TJ/LJ/YJ 1" Body Lift

    GenRight

    TJ/LJ/YJ 1" Body Lift

    This is a high quality urethane type 1" Body Lift for a Jeep TJ, LJ and YJ. This is the same type body lift we use on every GenRight Jeep we build.It is an excellent and necessary upgrade for Jeeps 2003 and newer to fit any brand high clearance gas...

    $299.99
  • GenRight's Axle Side 0 degree Lower Control Arm Brackets, BKT-3100 Shown here "tacked" into place in the proper rotation on the axle One piece design allows for more weld surface on the axle tube

    GenRight

    0 Deg Lower Control Arm Brackets

    These are top quality 0 Degree lower control arm mounting brackets from GenRight Off Road. Heavy Duty 1/4" thick is precision formed into shape so the mounting holes line up perfectly. Unlike the old days where fabricators just welded individual tabs...

    $69.99
  • Universal Urethane Bump Stop (Pair) w/ Bump Cans Same length as a compressed air bump stop, so you can upgrade down the road Shown here on the rear suspension with coil over shock Shown here on the front suspension set up for a coil over shock

    GenRight

    Universal Urethane Bump Stop (Pair) w/ Bump Cans

      This is the GenRight "Rock Stomper" Urethane bump stops. It is a simple and low cost solution for bump stops on a Jeep! Here is how it works: These Urethane Bump Stops fit in a KING 2.0" diameter air bump can. This allows you to...

    $299.99
  • GenRight's double triangulated rear cross member for a Jeep TJ Shown here being installed on a Jeep TJ Shown here with GenRight cross member kit and ASP-390 T-case support Shown here with GenRight BKT-1050 cross member kit and ASR-390 Extra plates reinforce the inside and bottom of the Jeep frame

    GenRight

    Double Triangulated 4 Link Crossmember Kit

    This is the GenRight Off Road design DOUBLE Triangulated 4 link cross member "only" kit for a Jeep TJ or YJ.Ideal to make your rig a top notch rock crawler with awesome articulation.We have figured out all the mounting points to optimize suspension...

    $799.99
36 of 79 Items